Wire mesh is also known as wire mesh, steel welding mesh, steel welding mesh, steel welding mesh and wire piece. The longitudinal and transverse reinforcement are arranged at a certain distance and right angle, and all intersections are welded together. Do you know what should be paid attention to before steel mesh welding?

　　當焊接鋼絲網粗糙焊接網不能曲折,焊接1 - 2鋼筋焊接網的少,然后兩個梁,和直接采用網站綁定方法,彌補減少橫向鋼筋,附加鋼筋焊接網連接的每個節點應選擇線綁定。在兩個焊接網的兩端之間，鋼筋搭接處的更小搭接長度不得小于更小錨固長度la的1.3倍。

　　When the welded steel wire mesh rough welded mesh can not be zigzag, and the last welded 1 - 2 reinforcement welded mesh is less, then two beams, and directly use the website binding method to make up for the reduction of transverse reinforcement, each node connected by the additional reinforcement welded mesh shall be bound by a line. Between both ends of the two welded nets, the minimum lap length of the steel bar lap shall not be less than 1.3 times of the minimum anchorage length la.

　　搭接區域內兩個焊接鋼網片有一非橫向配筋時，加肋焊接鋼網片更小搭接長度為更小錨固長度la的1.3倍，且不小于300 mm。搭接區域縱向受力鋼筋直徑d≥10mm時，應增加搭接長度5d使用。

　　When two welded steel meshes in the overlapping area have one non transverse reinforcement, the minimum overlapping length of the welded steel mesh with ribs is 1.3 times of the minimum anchoring length La, and is not less than 300 mm. When the diameter of the longitudinal stressed reinforcement in the overlapping area D ≥ 10 mm, the overlapping length shall be increased for 5 days.

　　焊接鋼筋網片底部網絡選擇螺柱位置和墊放置兩種方式,雙向竹節鋼筋焊接鋼筋網的面紗,宜選用方法的搭接接頭應設置在壓力相對較小,應設置從梁季度凈截面,搭接長度不應小于30 dd圈方向,強化和直徑不應小于250毫米。

　　Two methods are selected for the bottom network of welded steel mesh: stud location and pad placement. For the veil of welded steel mesh of two-way bamboo bar, the lap joint of the appropriate method should be set at a relatively small pressure, and the net section should be set from the beam quarter. The lap length should not be less than 30 DD circle direction, and the reinforcement and diameter should not be less than 250 mm.

　　那么，在鋼網的焊接鋪設中應該注意今天大家要完成哪些問題。焊接鋼筋網片鋪設前，應先擬定焊接鋼筋網片安裝方案，焊接鋼筋網片鋪設，根據現場實際及設備人員現場服務進行鋪設指導，以盡量減少焊接鋼筋網片鋪設時的麻煩。

　　So, in the welding and laying of steel mesh, we should pay attention to what problems we need to complete today. Before the laying of welded steel mesh, the installation scheme of welded steel mesh shall be proposed first, and the laying of welded steel mesh shall be guided according to the actual situation on site and the field service of equipment professionals, so as to minimize the trouble during the laying of welded steel mesh.